Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hi, I can make a DFU over BLE with nRF connect 2.5.0 Bluetooth Low Energy, all is OK. I use my nRF52840-Dongle PCA10059 (Serial port: COM19 | USB: Nordic Semiconductor nRF52...
Hello,
I'm using SPI 3 to communicate with a NAND memory. I'm able to go up to 8MHz but not more than that. Do I need to set an array list or use the spi manager.
Is there...
Hi Nordic Support, community,
Recently I started working with the nRF52 dongle, after flashing a hex file via nRFConnect/Programmer applic (version 2.5.running on Windows...
Can anyone tell me where the board / device choices in Eclipse come from, as shown in the screen shot below? I have none.
I copied my Eclipse installation from a working...
Hi all I've already setup my Eclipse environment as described in Development with GCC and Eclipse . Now I want to use the SPI libraries for my example. But I got the first...
Hi
The compiling of standard TWI sensor example is giving me an error with SES.
Please find attached a snapshot of the issue.
Need your help ASAP. Thanks
Ch...
My pcb is nrf52832 based, with SPI interfacing ICM20649 sensor.
- Nordic SDK 11.0
- Softdevice 2.0
I am able to flash example code of SPI based ble_peripheral and mpu...
Hello,
I am using an app_timer on my nRF52840 (SDK 15, Softdevice 140) to keep track of the time on my device. After a specific event, I would like to be able to clear the...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
I have been successfully using nRF Connect v2.5.0 on Windows with a PCA10056 v0.9.2 to communicate with our target device, a nRF52840 using S140 v6.0.0, nRF5 SDK 15.0.0. We...
I have four button and one external interrupt from GSensor on my demo board, and I use GPIOTE_CONFIG_IN_SENSE_TOG for button and GPIOTE_CONFIG_IN_SENSE_LOTOH for GSensor interrupt...
Hi, I am wondering what cost-effective JTAG debuggers you can use with the nRF52832 hardware using the 10-pin standard debugging header. For example, has anyone used the Segger...
Hi All,
I am using the nRF51822 board and have it connected to a micro SD card shield using SPI.
I have not changed anything in the example file with the exception of...
I have a question.
Two slaves connect one Master.
At that time, Can another Master automatically connect the two slaves ?
I know softdevice110_v7 has connection state and...
Hello,
We've been developing nRF52 software for about two years. We develop on Linux desktop machines, and build with GCC from the command line interface.
I'm starting...
