I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I downloaded the report from the official website in August 2023, but the client has given feedback that it has expired and they need the most recent one.
I would like to test GPIOE APIs on nRF5340 develop board. But west build generated the following warning message.
Could I use nrfx_gpiote _xxx related APIs ( infocenter...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
Hi,
I'm trying to use an nRF52840 dev kit as an I2S-to-USB microphone, but I've been running into a problem where the recorded audio is periodically unusable.
To debug...
Hey Everyone ... Looking for some ideas / help with crash involving nRF Sniffer v2 and Wireshark. Specifically I have an older White MacBook that I use for sniffing and nRF...
Hi,
I am using sdk 16.0 and I am already using 3 SPI Instances i.e. SPI1, SPI2, SPI3. I wanted to use SPI0 Instance also. How to use it?
If enable SPI0 in sdk_config I...
Hello
I was working on nrf9160-dk with assert_trakker_v2 application successfully connecting to nrf Cloud. There was no problem.
Today I started the day by deleting it...
From what I understand, the nPM1100 can work without the battery (i.e. no BAT connection).
Does the Nordic Thingy:53 come with the Li-Po battery separated or is it mounted...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...