Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am in the early stages of development and would like to proceed with only non-secure partitions on the nrf9160. I'd like to not make use of TrustZone.
I notice all of...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
What is the state of the GPIO pins during programming.
Because of space restraints, in order to get the the programming signals out from under the laird module we are...
Hello,
I am using a nrf52840-dk and communicate via SPI with an external board (NUCLEO-L476RG from ST) during development. For the development itself I am using the nRF...
Hi,
When starting to learn nRF currently, is it better to start with nRF5 SDK or nRF Connect SDK? I know Nordic will not add new features to nRF5 SDK, but what if I want...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
Hi All!)
I am using nrf52833/20 Dk and am able to connect the two devices using coded PHY connectable mode by the available examples ( BLE_App_Uart and BLE_App_Uart_C )...
Hi every body.
I have trying without success to attach an event handler function to the TWI.
I am reading a temperature and humidity sensor using I2C. In polling mode...
Dear Nordic Engineers
I would like to add usb bootloader to ble bootloader.
I modify config of pca10056_usb_debug/sdk_config.h and add .c .h file of pca10056_usb_debug...
Hi DevZone,
What I am working with:
I am working on a project using nRF Connect SDK with VS Code, and I am also using the nRF Connect extension for it.
My issue...
Commands sent by phone App to BLE UART end up in serial UART stream. Debug with breakpoint in the uart_event_handle shows NO stack entries, as though it popped out of Main...
To the kind attention of Nordic support team,
We are very interested indeed in finding sample AWTK porting on nRF52840 like in https://www.youtube.com/watch?v=zD-7YdxynLo...
my project requires a simultaneously data-collection from 13 IMUs sensors which we built with NRF51822 + BNO055 (IMU)
we used the Gazelle mode, I understand each host can...
