I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
With reference to the Thingy:91x reference design, I see that the LNA (SKY65943-11) on the GPS signal path is powered by one of the switching converters from the nPM1300:...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi, Firstly good day to anyone reading this query, hoping to find a solution for the issue here. I am trying to create a BLE device using nrf 52382 which transmits Audio file...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
Hi
On the nRF52840-QIAA-R there should be implemented the APPROTECT according to this guide:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/working-with...
I am developing an application for an NRF52840 using Zephyr and trying to run unit tests on startup. My application sources are in my src folder, and my unit ztests are in...
Hello,
I’m working on a Zephyr-based application using the nRF5340 where I need to optimize power consumption. The intended behavior is:
The device should stay in...
I had a driver made for my project, I now want to transform the driver into a module so I can use Git submodules and implement this driver in multiple projects.
This is...
Hi All.
Now I use soc:nrf5340, and ncs v2.9.0
I use QSPI to encrypt my external flash memory. Adding some print functions in xxx_encrypt can ensure that it is encrypted...
Hello, Have some experience with embedded development, but new to nRF Connect, sysbuild, Kconfig etc.
Using Windows host VS code with nRF Connect extensions - current versions...
Hi,
All my matter projects failed to build when working with SDK 3.0.x. It looks like some python issues. The error from the build log is below.
This happens with...
Hello,
When running the sample on nrf52840DK:
How to change the sample so that the 1sec on 1sec off blink pattern works?
I guess it has to do with the prescaler...
Hi all,
I’m working through Lesson 1, Exercise 2 of the Nordic Academy course (uploading the Blinky app to the Thingy:91), and I keep hitting this error: Firmware: C:\myfw...
