Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hello, I am working with the nrf52832 and was trying to understand the steps for configuring the Bluetooth stack. Does anyone know what role the APP_BLE_CONN_CFG_TAG plays...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
I'm evaluating nRF52840 as a candidate MCU for our next gen. electronics. I am following the DevAcademy class - all working well until I try to flash the (brand new - just...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I am using nrf52810 for ble peripherial , is there any sample project which has pass key authorisation , if not what are the changes need to incorporate in peripheral template...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hello,
For my Thingy91 I want to do some simple HTTP POST. I had a look at the https client sample (nrf/samples/net/https_client) and thought It could be a good baseline...
Hello,
The subject of this post is mostly accurate in that I am developing custom hardware that is based on the nRF7002DK. For all intents and purposes, the Interface MCU...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
