Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
After programming the DK, it "fails to verify device" with the following log:
2025-07-08T09:42:05.940Z INFO Initialising the bundled nrfutil device 2025-07-08T09:42:05.957Z...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I have a service and characteristic that is Notifying data at a rate of ~160 kbps.
Both our custom app and the nRF Connect app appear to be receiving the same packet over...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hi, I am trying to implement Angle Of Arrival. I am using direction_finding_connectionless_tx zephyr source code for transmitter (nRF52833 dk). It is advertising the packets...
Hello, I am the hardware researcher currently evaluating this product.
I am currently working with the nRF54L15 DK and have encountered an issue where my application appears...
Using NCS 3.0.0
When placing the app slot 1 in external flash, mcuboot cannot open the flash area.
I am testing this with nrf54L15 + 8 MB SPI flash on the DVK.
This...
Hi.
I'm using nrf Connect SDK v3.0.1 and Zephyr v4.0.99 to implement a IoT device which connects to a Thingsboard server with CoAP. With the COAP_CLIENT Lib I want to download...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
Wonder if anyone has experience this but my Zephyr OS and a http client application eventually crashes due the network interface going down coming back up. Initialization...
I am using the following version of nrfjprog on my Windows 10 machine:
nrfjprog version: 10.24.2 external JLinkARM.dll version: 8.44a
Most of the sub-commands work with...
