We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack. ...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all, I am working on an nrf5340 and I activated the FileSystem Backend log to save the logs in my external Flash. It's working how we are expecting to except once the flash...
Hi,
I'm experiencing high packet loss with the application nrf5340_audio example, I'm using nrf5340 audio DK as a unicast server, and then I'm using a Sony phone to connect...
Hello, I am using nRF52832, nRF5 SDK, s132, and DFU-OTA with private keys and secure bootloader I am trying to enable the DFU Downgrade by disabling the define NRF_DFU_APP_DOWNGRADE_PREVENTION...
SDK:11.0 Example:ble_app_hrs\pca10040\ s132_with_dfu
Hi Does nrf52810 only support a maximum of one central connection at the same time? If I currently want to connect two...
We wanted to understand better the use of external NOR Flash for nRF9161 applications. For example, in nRF9161-DK, this would be the GD25WB256E chip.
For modem delta fw...
Hi!
I just succesfully flashed my modem firmware to version 1.3.6 using the nrf programmer and a segger external programmer. I can still connect over the serial monitor...
I used nRF52840 board with SDK 17_1_0 ,
I want to used WS2812B in my project so any one can give me reference code for this or
can suggest me how can i implement its driver...
Hi,
I am using nrf52840 and SDK-16.0. Initially I was using SPI1 and SPI2. now along with this I am using SPI3.
we have added new feature which consumes 316*9*26 bytes...
I am trying to cancel a pending connection as a workaround for .
However when I run:
```
LOG_DBG ( "Peripheral connection timeout cancelling and trying later" ) ;...
Hello . I saw this issue raised previously but with no resolution so here it is again
I built the smp-svr sample in VSCode with Zephyr SDK 2.6.1 which produced a DFU package...
Hi all,
The question is about 125kbits and 500kbits long range modulation in proprietary protocol. I'v seen a post saying that is technically possible ( ).
But is...
Hello,
I have a project in progress with an NRF52840 chip. I was able to buy an aircard with the same chip www.kickstarter.com/.../aircard-find-your-wallet-always With this...
I receive the following error message when trying to install the toolchain manager (V 1.5.0) from nrf connect for desktop (V5.0.0):
Error: Failed with exit code 1. Failed...
I've been experimenting with the nRF5340's HFCLKAUDIO clock, and have discovered a discrepancy that I cannot reconcile. Table 23 in the datasheet details the peripheral's...