Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi，
In the NCS V2.3.0 version, I successfully obtained the serial device through the following code and compiled it But when I get the serial device in the same way in NCS...
Hi,
Sorry to be posting a lot about my LIS2DH12 on custom hardware lately. I do believe my different inquiries are to be treated as separate.
My (modified) hardware now...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hi,
I'm using nRF5340 Audio DK with the audio example code in BIS mode. I would like to set the broadcast name during runtime, and not before compilation. Namely, I want...
Dear support team, We need to integrate DTM function into matter. We have disabled bt, but it still prompts that radio_init failed. Do we still need to disable matter protocol...
We are trying to setup image encryption in our nRF build, for use with BLE DFU.
I see that this is not supported by Nordic, but that there is support for it in MCUBoot....
I want to add the timer sample code to my own project "../src/main.c:11:10: fatal error: nrfx_example.h: No such file or directory 11 | I'm encountering the error #include...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hi,
I am using the NRF52832 DK version 3.0.0 with a UWB module: the DWM1000 from Qorvo.
I was struggling with the SPI communication to get the Chip ID by sending a simple...
Hello,
I am working with nRF52832 and want to put it to sleep and wake it up with a interrupt from a GPIO. I am using a accelerometer LIS3DH to generate the interrupt. I...
Hi,
We're using nrf Connect SDK v2.4 and have issues when calling bt_gatt_notify() from our main thread. The bt_gatt_notify() function blocks even though we have the CONFIG_BT_L2CAP_TX_BUF_COUNT...
I merged two sensors, BME and BMI, and checked the raw data output through NRF_LOG_INFO. Now, I've added the new merged code to the main firmware, but the log for the BMI...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
Hi all,
I am developing a project with the nRF52840, using nRF Connect SDK 2.6.1 in Visual Studio Code.
I need to be able to compute an MD5 checksum for a dependency....
