Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello there,
Working on bringing up the FOTA feature on the 54L15. I began with the LBS example. I was using the Nordic "Device Manage" to push the FOTA build.
The state...
I've been using the following SPI2S pins and they've been working:
CLK -> P0.16 MOSI -> P0.17 MISO -> P0.19 CS -> P0.18
I want to use SPI1 instead but when I replace...
I have a two fold question, to build a prototype, I would like to know how to get
tflite micro in zephyr build for nRF9151 DK?
Non-Terrestrial Networks (NTN) on above...
I have been using the nRF Connect for Desktop with the Programmer application for several years to attach our end device to the Dev Kit to program our device with no issues...
Hi
Can the device(nrf52832) be used as a BLE Mesh Provisioner and Light Switch Client(such as Generic OnOff Client) at the same time?
I want to develop a device (nrf52832...
Thanks in advanced. Based on nRF5_SDK_17.0.2, I can use i2c with icm42670p normally. Due to power consideration, I need to r/w this imu with spi either to decide which is...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
Hello.
I need to read IMU data from LIS2DH12 of nrf 52833 which is in DWM3001CDK. But nothing I do initializes sensor... i always receive
<err> lis2dh: Failed to read...
Hello!
I am learning to obtain data by SPI protocol from ICM20948 sensor using nRF54l15. I tried to write my code based on sample given on devacademy nRF Connect SDK Intermediate...
We are developing with the nRF9131EK. But there is no documentation of this board.
https://docs.nordicsemi.com/category/nrf-91-series
Can You add the information like...
Before developing our custom board, we connected our MCU to the DK via pins 26, 27 and after disabling VCOM0 via the DK configurator, we were able to communicate using AT...
Hello,
I wanted to know if the "direct test mode sample" could be used for the EVK-ANNA-B402C that integrates the nRF52833 in its SIP.
Because building with the board...
I have a nrf52840dongle and a nrf54l15 custom board. And I flashed bt hci_usb demo into nrf52840dongle, uart_peripheral demo into nrf54l15 board.
Now I want to use my nrf52840dongle...
I am performing a BLE DFU update on an nRF52840 using the nRF Connect Android app (v4.29.1) . The app successfully uploads the DFU package and reports that the update is completed...
