Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello Nordic team,
I'm developing a proprietary radio protocol and I'm using CCM peripheral for on-the-fly encryption. The packets seem to be correctly encrypted and decrypted...
Hi, I use nRF52840, with SDK 15.3.0
Using UART communication, stored data should be unsigned integer 16 bit.
And the data should be calculated to float data type.
...
Hello there. I am wondering if PWM peripheral in waveform is able to generate a following sequence:
The idea, as you may see, is to generate a sequence with the same Duty...
Hello!
We have hit a wall trying to add support for a particular BLE peripheral to one of our products (which is acting as a BLE central). We support other peripherals,...
Hi Nordic Team,
We have no problem with using ble_app_hids_keyboard app,
However, in some use cases, we would like the application to run as "Just Works" to access other...
Hello everyone,
I'm currently developing a custom firmware for the Nrf52840 usb dongle ( https://www.mouser.de/new/nordic-semiconductor/nordic-nrf52840-usb-dongle ). The...
After power-up and RESET by RESET pin, power consuption of nRF9160 is ~2uA.
After wakeup by WAKEUP pin and AT#XSLEEP=2 power consuption is ~23uA.
What causes increased...
My goal is to use the atmel winc1500 wifi module with the nrf5340. - NRF5340 - NCS V1.9.0/Windows 11 - Atmel winc 1500 I started from the http_client sample (ncs\v1.9.0\zephyr...
Hello, I have soldered up a 51822 and I am trying to connect it with an EmStat pico and get measurements. I am not sure how to program the chip and get it discoverable with...
Hi,
I am using the NRF52840DK and would like to configure the GPIOs to have levels of 1,8V by using zephyr 2.4 or zephyr 3.1. By default I am getting 3 V.
Can anybody...
Hi,
I need help to use FT2232H wit OpenOCD for flashing and showing debug messages from nRF52833 Dev Kit.
Background:
I need to distribute the debug environment to...
Hi there,
We are implementing the %CONEVAL AT cmd in our project and noted that the DL-Pathloss parameter, which is supposed to be the last parameter received, is not being...
I have 3 development kits, two of them work fine with the Audio demo application and one does not: the PLAY/PAUSE button isn't doing anything.
I've probed around the switch...
