Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
We are using an MCU that pushes data packets to the nRF9151 communication module via UART. According to our module service provider, each data packet can only be up to 2 KB...
I am testing PAwR interoperability between:
TX side : third-party chipset acting as PAwR Advertiser/Transmitter
RX side : Nordic board running nRF Connect SDK...
Goal: "I am trying to get SPI3 working with a custom MAX30003 driver in a sysbuild non-secure ( _ns ) application, based on the peripheral_uart example."
Problem: "The...
Hi,
I have been evaluating the use of nrf9151 using two development kit boards.
On my first board, I set it up initially using quick start under the nRF connect app...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, I encountered a problem while using the nrf5 SDK. In my software, I used a UART for debugging data output, a libuarte library for command output, and an app_button...
I'm trying to use nrfutil as part of a script that sets up the toolchain environment automatically using direnv .
For example:
I'd like to know how the bundle ID can...
As subject, NCS 3.0.2, I use demo 'peripheral_power_profiling' to test current on NRF52832 DK board, but the demo cound not run when power on, There is no log output, and...
Hello,
I am exploring power management on the nRF54L15 DK with nRF Connect SDK v2.8.0 (Zephyr v3.7.99) .
My goal is to:
Enter deep sleep / system off mode.
...
I am trying to wake up the NRF54L15-DK from deep sleep using RTC. The device goes into deep sleep but never wakes up. I would like to know if RTC can wake up the micro from...
Hello,
I am trying to run the wifi_scan example but I am getting a BUS FAULT error as seen below. The SDK is v3.1.0, and the SDK Toolchain is also v3.1.0.
1. Going...
i have version 0.9.2 of the nRF54L DK....
i've noticed there is now 1.0.0 documentation....
have there been any HW changes -- use of "production" MCUs, etc....
more...
Hi Team,
We are looking into the new Thingy 91 X and were wondering if it will be able to run the nRF91 Pizza Demo .
I understand the demo was originally created for the...
Hello,
I'm working on Windows 11, with the nRF Connect for VS Code v2025.5.512 extension, with ncs v3.0.2. I'm using the nRF54L15-dk (PCA10156; 0.9.2; 2025.7) development...
citing the following issues
I've been able to implement the 16 Mhz on the SPIM3. However, the incoming data on the MISO is still corrupted. With my oscilloscope I can...
