Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Currently, we are developing our own board with NRF5340-CLAA. It does not have a 32.768kHz crystal oscillator, only an external 32MHz crystal oscillator. We have applied the...
Hello, I need to do some RTT trace logging, but I can’t enable it. I am trying to create minimal example code, and for this purpose I am using the UDP sample. I added these...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hello, the time to ask for help has come again... I keep hitting a crash in my BM833 code related to "Illegal use of the EPSR". Code is fairly simple and supposed to be pretty...
Hi,
hi have the same problem related here: https://devzone.nordicsemi.com/f/nordic-q-a/91890/nrf52-reports-two-jlink-cdc-uart-ports
With revision 2, UART show only one...
We are looking into a device using the NRF54L to do low power indoor tracking since it has a very low power consumption when using the RADIO peripheral.
We see that the...
Hello,
I am facing an issue with nRF Cloud device provisioning. I am using the nrfcloud-util tool to provision the device to nRF Cloud (as recommended for production provisioning...
Hi all,
I’m running into issues flashing an Arduino Nano 33 BLE Rev2 (nRF52840) using Zephyr and the bossac runner. I consistently hit a “Flash erase failed” error and can...
Dear Nordic,
We’ve developed an application which runs on an nRF9151 DK using NCS 2.8.2. The device is running modem fw nrf91x1_2.0.2. Our application has enabled modem...
Hi I made a small production run of boards using nrf9151 where a handful of them have issues with nrf9151 such as not being able to flash. How do I debug the circuit at the...
Hi, I have a simple question. Is it possible, during the execution of Channel sounding ( ras_initiator ), for the initiator to regularly obtain the current RSSI from the reflector...
I am trying to flash an application image in nRF9160 on Thingy91. Thingy91 is in MCUBoot mode, and the selector switch is on nRF91 position. I get an error as below if I try...
Hello,
I am facing an issue building the NCS v3.1.0 Matter light bulb sample for nRF52840-DK:
cluster-enums-check.h:151:10: fatal error: clusters/TotalVolatileOrganicCompoundsConcentrationMeasurement...
