Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
Hello
I am trying to perform a firmware update over Bluetooth but without using the external flash on the nRF52840-dk.
At this point I can successfully build the smp_svr...
Hi,
I have custom hardware using the NRF52810. Due to its very small RAM size, I developed the code on the NRF52DK_NRF52832 and then removed functionalities to make it fit...
Hi The Nordic team,
After my device reconnects to the gateway from offline again, I don't know what I am doing with this timing every 1s. This situation will not happen...
Hi，
I developed a gateway for converting an MCU to ble Bluetooth. The MCU connects to 8 BLE hosts via UART, and each Bluetooth host can connect to one Bluetooth slave. All...
Hello,
I am trying to configure COMP peripheral on my NRF54L15 DK. I am using P1.11 pin (AIN4) as single ended input for this purpose. For now I am trying only to evaluate...
Hello,
I’m working on a project where I intend to integrate the nRF9151 as a standalone modem , communicating with my external MCU via UART using AT commands .
My goals...
Hi,
Currently I am using nRF52840 as nodes for mesh network. However, by reading the sdk5 documents and example, I did not see any clues to update the firmware with DFU...
After the update to extension version 2025.8.654, the extension can no longer find the nRF SDK in my west workspace in the build configuration. If I revert to extension v2025...
I made a PCB board, but I couldn't connect to the chip with JLink. I used a lithium battery to power VDDH. I want to test if there is any problem with the hardware. I tried...
I am using NRF5340 with NRF connect (Zephyr) and logging out to RTT (printk or printf, etc) , which works but sometimes I get buffered fragments and dont see the rest of the...
Product: nRF54L15, SDK:3.0.2, door lock application
Hi,
When the Matter door lock removed from Apple Home(Home App, remove accessory), the lock does not remove all the...
Hello,
I am experiencing an issue when trying to flash any program using nRF Connect for VS Code. When I execute the flash command, my board disappears from the "Connected...
Hello,
Is there support for fuel gauge algorithm with the CR2450 and the nPM2100 implemented? If not, is there a plan to release support for it soon?
Thank you,
Fin...
