Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
I use nRF52810 SoC to forward data between BLE and UART on our product. So I initialize UART interface and set some GPIOs once enter the "main" function in my codes. But we...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
Hi,
I need the SAADC of the nRF52840 to do the following:
It should sample two channels as fast as possible for a certain time (or for a certain amount of samples)....
Hello,
I have tried to upgrade a working project from ncs 1.5.0 to 1.6.0, which used the shell + console + RTT. However, long commands (more than 16 chars) seem to be truncated...
Device: nRF5340 DK
I installed the SEGGER Embedded Studio and wanted to run a sample application. But it throws an error when I click on Connect J-Link.
But I see that...
Dear friends,
When I reset 52840 DK and reopen the PyACI script , then, reloading the DB(database/example_database.json), I found the provsioned device can't be controled...
Hi sir/Madam,
Kindly provide the uplink and downlink details for the part
nRF9160.
We request you to provide the quote for 50K/Annum.
Please contact : lakshminarayanan...
