Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
I have some code that used to compile using version 2.5.2
I'm trying to move to 2.7.0 and have my own manager for TWIM that needs to intercept the TWIM interrupt.
In earlier...
I'm trying to use littlefs in Zephyr with SDK 2.7.0
My code is based on the example project "littlefs" and it compiles without problem using SDK 2.7.0
I'm using nRF Connect...
I am experiencing an issue with my board, where I have interfaced an nRF52840 with an LSM6DSV16 via SPI.
The nRF52840 chip, once started, can decide whether or not to...
I am trying to get an LED attached to GPIO to turn on. I have tried all documented methods I could find but with no success. I have no issue controlling the onboard LEDS but...
Having trouble creating the zephyr DTS DTSI files for i2c0 for the nrf54L15. need to get the initial definition correct,
actually using dtsi
& i2c0 {
compatible =...
Hi everybody. I'm using nRF Connect SDK 2.8.0. I've implemented Zephyr RTOS' core dump functionality on my project. I forced the SoC to write the core dump data on its flash...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The USB pin connections are designed based on the nRF9160-DK's nRF52840 reference....
I would like to be able to open a bash prompt with the nRF Connect SDK (NCS) v2.0.0 toolchain environment loaded without going through Toolchain Manager ("open bash" option...
We are evaluating the nRF5340 chip for a Bluetooth LE audio broadcast streaming application.
Is it possible to use adaptive frequency hopping with the BLE audio network...
For the RADIO peripheral of the nrf52(840), if you set up the radio to receive coded Phy transmissions, I have the opportunity where I can set the MODE for 125Kbps or 500Kbps...
I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex".
I've then tried both the command...
When I use nRF Programmer on my laptop (v3.0.7) to update firmware on my Thingy53 with a USB cable and SW2, the programming seems to finish normally, but it prints "Bluetooth...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...