I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
I am working on a project with channel sounding requirements and I have collected some test data. I am using the example codes Bluetooth: Channel Sounding Initiator...
I am developing an application using nRF52833 + nRF5 SDK + S140, and I encountered a strange issue. When I perform an OTA update from a firmware that does not initialize the...
Hi there,
I am using MDBT dev kit based on MDBT53-1M module. I have a simple application of reading an SD card and printing the data on the LOG. While the current application...
Hi
for DFU is bluetooth used by default. Your DFU app suports only using bluetooth to do a DFU.
Do you have any tools to do a DFU over NFC? Or do I have to write a tool...
## Summary
When running the OpenThread CLI sample on `nrf54lm20dk/nrf54lm20a/cpuapp` using nRF Connect SDK v3.2.4, the application crashes immediately on boot with a ...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I have an application that gets a fix using A-GNSS. I couldnt understand from the documentation how to enable other satellite systems other then GPS to be enalbled in my application...
Hello,
I am trying to run this Android-nRF-Blinky sample from Git ( https://github.com/NordicSemiconductor/Android-nRF-Blinky ) and build failed.
Below is the error message...
I make a BLE/USB MIDI controller that has an NRF52840 receiving sensor data by SPI from an Atmega 32u4 at 2Mhz. The NRF52840 is the SPI master (SPIM3). When I'm using BLE...
Hi there, I am using nrf connect sdk v2.6.0. I have noticed that after DFU update, I am seeing ble bonding lost randomly on firmware side. I did uncheck Erase Application...
We are running some sample code on the nrf54l15 mcu, specifically: /modules/lib/memfault-firmware-sdk/examples/nrf-connect-sdk/nrf5/memfault_demo_app
We can connect and...
Hi nRF support team,
I am evaluating ST7735 LCD with the nRF82540 development kit. For your information, I am able to set-up the nRF Connect SDK environment on nRF82540...
Hi Sir, I am developing with the nRF52840.
I installed nRFConnect 5.2.1 and the programmer (version 4.6.2), Following the programmer’s prompts, I installed SEGGER J-Link...
SDK version: 3.2.4
I am using two nRF5340 Audio DK boards configured as gateway and left headset.
I added " CONFIG_STREAM_BIDIRECTIONAL =y" to prj.conf and I built everything...
