We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi Team,
The customer have used NRF52832-CIAA-R. The datasheet of the Bluetooth module has NFC function. Please help provide the reports of EN 300 330-1 and EN62311 for...
Hello Nordic Forums.
I have been struggling for the past couple of days to try to get the SPI working. I never thought that something this easy could have become such a...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
We are checking the feasibility on LE Audio + Mesh + Bidirectional streams. A picture is attached for the situation. We would like to know how to apply Mesh network on LE...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hello,
We have a requirement to ensure all private keys are stored within AWS Key Management System (KMS) and the only way to interact with these is via the KMS APIs that...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I recently had a question about AES encryption on the nRF9160 and about how to store 32-byte encryption keys. The ticket was closed after I got the following answer: " we...
Hi,my board is nRF52840,and the demo is periodic_sync_conn within ncs2.7.0,
I want to establish periodic sync with the AP whose rssi is better，but i am failed。The ESL will...
Hello Nordic team,
I am working with the samples/bluetooth/shorter_conn_intervals sample on NCS v3.2.3 using two nRF54L15 DK boards.
I understand the difference between...
Hello, Recently I got an nRF9151-DK and I am following the Cellular IoT Fundamentals course. When it was time to connect the device to nRF Cloud (Lesson 1, Exercise 1), it...
Hi there,
I am developing a Matter light color temperature lamp product based on the NCS v3.1.1, and I need to store some custom user data in NVM (Non-Volatile Memory) within...
