Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
NCS 2.4.1 nRF52840
My project is a battery powered SED based on the coap_client example. It is configured to autojoin using a hard coded pksd. I see on Wireshark that my...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
Hi,
I referred to this doc for hardware setup
However, in the programmer in nRF Desktop, I got the following log:
17:37:36.199
Error: Failed with exit code 1...
Hello person in charging,
I would like to know whether there are something information on vulnerabilities in the proprietary mode of nRF51 and nRF52, respectively.
Thanks...
Hello,
After an update to the NRF connect for Desktop the Programmer application can no longer program my nRF52840 dev kit (PCA10056, 3.0.0). Trying to revert the update...
Hi,
In our project, we're using Mcumgr FS to download files from our device.
After tweaking the BLE configuration parameters using the throughput sample ( https://github...
Hi
The datasheet of the nRF9151 is missing the statement in the nRF9161 datasheet:
RF 3GPP compliancy requires 3.3 V.
Is the nRF9151 reaching compatibility down to 3V...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
