Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Dear all,
I'm developing a 1 VS 4 BLE connection system, using 1 nRF52840 as BLE central and 4 nRF52832 as BLE peripherals.
I'm trying to send the same command to 4 peripherals...
Good Day,
We build a custom board with nrf5340 & nrf21540,
NetCore DTS (below) , NetApp DTS has the gpio_fwd in place , all looks good in .config generated. Net-core UART0...
Hi,
I've been trying to set up UART communication with external device using uart3 instance and have so far failed.
The scenario requires sending 5 bytes to the device...
Hi!
I'm trying to portnRF7002 QSPI bus driver for one of the NXP MCUs. Communication with nRF7002 under Zephyr is already established and everything works as expected. ...
Hi
I compiled an older project using embedded studio and flashed my NRF dongle. Now the USB DFU bootloader seems to be gone.
How can I restore it?
Several links on devzone...
Hi
I am using hci_pwr_ctrl and want to get the RSS (read_conn_rssi(default_conn_handle, &rssi) in a very high frequency. However, I notice when I use 100Hz frequency, a...
HI there,
I've been following the DevAcademy Lesson 5 exercise example on SPI communication to get a nRF9161 DK (as a Master) and an ESP32 (as a Slave) to communicate synchronously...
Is there any othere way than mergehex to merge application core and netcore hex files? I'm not sure if I'm following correctly, but it seems like it might be possible through...
I would like some help with porting the modem library (nrf_modem_lib) to work with my bare metal application. Besides a custom nrf_modem_os.c, I have made a slightly modified...
Hi!
Running LTE_BLE_GATEWAY example on nRF9160DK rev 1.1.3 gives "No HCI driver registered" error together with "Bluetooth init failed (err -19)". SDK/Toolset version is...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I have been developing in the nRF Connect SDK for a few weeks now so I am fairly new. I have...
When using the distance measurement sample code on my nrf5340 development kits, LEDs 1 and 2 seem to be working correctly, but LED 3 does not light up when connected. The...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hi All,
I recently received a few dev kit boards that I intended to use for a test fixture we are building. I tried to use it in our test fixture which had been working...
