Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello everyone, I'm new here, and new to using the Nordic boards. I have a question regarding the RF connector in the nRF52840_DK. I am trying to do some RF measurements with...
Dear Team,
We notice that systemOFF current varying from 220 nA to around 500 nA for different devices. For some devices we are able to achieve 300 nA as mentioned in the...
Hi,
I'am using the ble_uart example on a custom board, where I have the issue that the BLE advertising is only available after a reset OR when I comment out the uart_init...
Hello,
I would like to implement beacon feature with a periodic (each 10s) advertisement data update.
This is an extrapolation of my code:
Is there some function that...
Hello,
The part i am using is NRF52840 Rev 2 (Build Code Dx0)
How can i exact know what revision or build code the SOC has ?
I want to determine in application what...
I am using NRF5 SDK 17.1
SES
S112 for the nRf52805
I followed the guide for the 805
i then used the NUS Peripheral and was trying to setup the rtc so the device...
Hi,
I have a nRF52840 Preview Development Kit. I studied your manual, but I didn't quite understand if this is possible or not?
I would like to debug (therefore I...
Hello,
I have been testing an encoder using the QDEC peripheral.
The encoder produces 256 pulses per rotation. Testing without any load assigned to the motor, the encoder...
In SDK11 through 17, MCLK is limited to 16 selections. None of which match the 256 x LRCLK or 384 x LRCLK standard. I looked at the CLOCK, thinking I could assign it as a...
I am working on nrf52840 with nrf connect sdk zephyr example scan_adv, I want to modify it for example scanning for 2 second and advertising for 5 second, I tried to use ...
Hello
I am trying to change the code from the HAL code up to NRFX in order to make it event-based instead of using infinite while loops.
I am using 52840 on a custom...
I am developing a bicycle powermeter using the XIAO BLE nRF52840 Sense Breakout board with an AD7799 on a dedicated PCB i also made. I use Segger Embedded Studio v5.42a and...
Hello,
I have now one application that runs on two different boards with different device tree. So inside VSC (Visual Studio Code) it Looks like (under nrfConnect)
Under...
I know part 15 talks about bluetooth requirements, could someone tell me precisely where the FCC says bluetooth devices need a 32 MHz external clock source? Thank you
Hello, recently i've been trying to test the nRF9160-DK.
I flashed the program simple MQTT to the board, I changed all the configuration in order to connect to the server...
