Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
My nRF52840 was recently corrupted. I was able to run through reset and downloaded the latest MCU 'J-Link OB-SAM3U128-V2-NordicSemi 170724.bin' onto the board. So now it shows...
We are preparing a product (based on nRF52840) for manufacturing and currently defining the production test process.
The product is hermetically sealed with no external...
Hello,
I'm currently implementing a multi-endpoints Zigbee device using an nRF52840.
This device is a router which have several "GROUPS" clusters (one in each endpoint...
Hi,
I've nrf52840, s140 with SDK17.2 and I was able to set REGOUT0 to 3.3V in 2 ways.
or
nrfjprog.exe --memwr 0x10001304 --val 0xFFFFFFFD
After that I do...
It is my understanding that the more antennas you use for AoA the more memory is required. I am trying to gauge how much memory and resources would I have left for other application...
Is there a way to configure the serial LTE modem application to communicate through the UART using a 2-wire Tx/Rx with Hardware flow control disabled?
I have read that you...
We are trying to switch main MCU that we use in our products into NRF52/53 series devices. We've chosen NRF52833 (aQFN73) for one of these devices. Is it possible to use only...
Hi,
I have a question about the LwM2M Client implementation for the nRF9160.
Can the LwM2M Object updated in a registration update or it is relying on a re-registration...
I have a situation where a customer needs to DFU some nRF52840 custom boards that we shipped. The firmware that I wrote used extended advertising and thus appears as a Bluetooth...
Hi,
I tried running the crypto sample example as part of the nRF SDK project on my nRF5340 DK.
I successfully completed as few tests and then fails while trying to run...
Hello Nordic Team I want to use the ble_app_beacon example found in SDK 15.3 on NRF52810 when NON_CONNECTABLE_ADV_INTERVAL is MSEC_TO_UNITS (5000, UNIT_0_625_MS). The program...
We are using the QDEC in an nRF52832 and our rotation speeds are 0 to 15rpm, usually around 10rpm. Is there any fundamental reason the QDEC can not be used in this case? We...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
