Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi, I want to add PPP protocol to the Zephyr mqtt_azure example. I am using an nRF52840-DK with a Quectel BG-96 Modem. The generic Zephyr gsm_modem example using PPP is working...
Hi, I am using nrf52840 with S140 Soft device and SDK for Thread v4.1. In our test setup we got around 50 FTD devices in the same network. In some time interval we need to...
We are trying to connect the nrf9160 to a spi flash device. we have a custom board with the following pins connected:
sck: 27
mosi: 28
miso: 30
cs: 29
wp: 31
reset...
I would like to use the CC310's SRP accelerator with an application that uses S140. The uC in question is nRF52840.
I have added this code to the ble_app_blinky example...
Hi,
As per nRF52840 datasheet, the accuracy of internal temperature sensor is ±5°C. We want our device to be operational between 5 °C to 40 °C.
When we tested this extreme...
Hi,
I want to use the Zephyr network stack with its libraries on the nRF9160.
I tried to use the Zephyr tcp functions with the Zephyr network shell commands (eg. shell...
Hi Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports Dual Bank DFU. This limits...
Hi Team,
We are using the nRF52840 for our development purpose. For sake Cyber security purpose we need to disable the Jtag debug port.
For this we have used the below...
Hi Team,
We have seen 10 instances in past 2 months where customer mobile phones failed to discover BLE device. This has happened 8 times with Moto G7 power (Android) and...
We have a module based on the nRF52840, today we loaded the pre-compiled hex file for the BLE DTM code to 2 nRF52840-based modules and noticed when using the nRF connect DTM...
Hi !
I want to whiten the BLE Advertising data(channel 37,38,39), but I don't know how to do it.
I tried many things, but nothing worked.I'm on 52832 platform Flash_S132_NRF52_7...
Hello,
I have got three nRF52840 Dongles to test Bluetooth mesh. I have been going through the devzone queries and found that many people have previously asked about SDK...
Hello,
I am using the nRF52832 with the s132 SoftDevice. I've been trying to interface the VL53L0X sensor to get ToF readings. I'm using the code of this driver . When calling...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
