Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi!
After some work with the otherwise exceptional Power Profiler software I find the current screen layout annoying:
The current display is in sync with the digital...
Hi,
I like to measure the VDD in nRF54L15DK using ADC.
I have flash the example firmware ..\v3.1.0\zephyr\samples\drivers\adc\adc_dt in my DK.
I can see it is measuring...
Hi, Good day!
I’m currently working on the nRF52832. The requirement is to support BLE + LoRaWAN (SX1276) .
I have a few questions:
How can I set up the LoRaWAN...
Hello, I have a question about the power consumption stabilisation of the nPM2100. We configured the nPM2100 with the pins directly to obtain a V_OUT of 3V with a 2477 battery...
Hi,
We are currently considering the performing DFU with UART with another MCU. Is there a sample for this application where nRF54L SoC is being updated by another embedded...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2) and we would like to benchmark current consumption...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi everyone, I am attempting to measure I2S rate against internal clock frequency since I am using APLL. I am following examples in NRF5340_Audio application. What i have...
Currently, I'm using the NRF5340 chip. In my own development board, I'm only powering the chip to test its transmission performance. The example program I'm using is the classic...
nRF52840 using Zephyr 2.0.0
We currently have a system that after we are running can drop to 20uA. However, on boot, we draw something like 5-7mA. This large on boot current...
I work on a project with nRF52833 ( NRF Connect v3.0.2 currently) and I have to use an external AT45DB641E flash chip connected over SPI .
The external flash will be mainly...
example: ncs/v3.0.1/find my/pair before use I want to implement the ptx and prx of the ESB in the find my example "pair before use". That is, how do I operate when both BLE...
In our application we need a PPS signal even when LTE is enabled (and GNSS is disabled). The GNSS API gives some encouraging PPS info, stating " GNSS only starts giving pulses...
