I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I'm trying to connect to the nRF52840 dongle using nRF Connect for Desktop Programmer v4.5 on MacOS 15.2 so I can update the firmware. The dongle has the red flashing...
I've then tried both the command " nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded" as well as "nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded --scan-follow-aux...
Helo,
I lost the PUK to my iBasis SIM, so I can't register it on nrfCloud.com for my 9160. Is there a way to recover it or do I need to buy a new one? (If so, where?)...
I tried to write the following simple '.overlay' file:
However, I am getting the following error:
but if you look inside the .dts files provided by the 'nrf52dk' I...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
Hello everybody! There is a problem and help is needed. With the help of hardware timers, I need to generate a signal with a given accuracy. The frequency is 998 Hz. I'm using...
We are working on developing wearable device (like band) with cellular-IoT network connectivity. Considering available features and size, nRF91 series seems to be a good choice...
Hello
I am developing an application in which I am using a timer expiry function to submit an event periodically. My application is using the Application Event Manager...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi there,
I have recently moved to nRF5340 for my audio recording application. I have successfully implemented I2S master on nRF5340 using SPH0465 mems microphone as a...
I have some code that used to compile using version 2.5.2
I'm trying to move to 2.7.0 and have my own manager for TWIM that needs to intercept the TWIM interrupt.
In earlier...
I'm trying to use littlefs in Zephyr with SDK 2.7.0
My code is based on the example project "littlefs" and it compiles without problem using SDK 2.7.0
I'm using nRF Connect...
I am experiencing an issue with my board, where I have interfaced an nRF52840 with an LSM6DSV16 via SPI.
The nRF52840 chip, once started, can decide whether or not to...
I am trying to get an LED attached to GPIO to turn on. I have tried all documented methods I could find but with no success. I have no issue controlling the onboard LEDS but...
