We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
Good day!
Statement of problem: In our application, we are using nrf52832 SoC to control critical components (heater). So I was suggested to use a watchdog timer to...
Hi,
Im trying " https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/main.c " gsp example to check supl(AGPS) to integrate into my application...
Hi,
In-app when you scan for device and after it is found you press the connect and then the notification/permission to pair pops out. Our app developers are saying that...
Hi,
We are using nRF51DK for our development, we have developed Android app for Android smart phone.
When the Nordic BLE device advertising we are trying for BLE connection...
Hi guys,
I'm fairly new to this kind of stuff and I'd appreciate if someone could point me in the direction of how I would go about taking the data being transmitted by...
Hi nordic,
I am using SDK15.0 (NRF52840) to design a watch producation which needs pairing. I have a problem that if NRF52840 (peripheral ) has been paired with a smartphone...
I want to get the RSSI of a connected device. The sequence will be as follows:
int8_t *p_rssi;
uint8_t *p_ch_index;
sd_ble_gap_rssi_start (m_conn_handle, BLE_GAP_RSSI_THRESHOLD_INVALID...
Setup: nRF52840 DK nRF52 SDK v16.0.0 s140 v7.0.1 When I attempt to use the nrf_crypto library for AES 128bit ECB encryption I keep getting
NRF_ERROR_CRYPTO_CONTEXT_NOT_INITIALIZED...
'm sending a publication set message (0x03) from an iOS app to an nRF52840 board using the light server example in the latest SDK. This works and I'm able to receive messages...
Dear All, I would like to know which is the better GPIO configuration to drive a LED for extremely low power consumption. We have a board with nRF52832 SoC with GPIO connected...
Hi,
I have Android (8.1.0), and installed nRF toolbox 2.8.0. To update firmware using .zip file.
The DFU Upload returns error:
Unfortunately, nRF Toolbox has stopped...
The 3GPP Release 14 introduced new, third power class of 14 dBm for NB-IoT devices. Is it possible to assign nRF9160 to operate at the lowest power rating class, the 14 dBm...
Hello everyone,
I am working on a project where I need to interface an NFC reader (trf7970a from TI) to an NRF52840.
I got everything working fine, but I have a major...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
