This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi
When running a project on the nRF54L15 using nRF Connect in VS Code, I often cannot connect to RTT. I select RTT in nRF Connect, but no output appears. If I retry multiple...
Hello,
I am able to reproduce this issue in a blank project where CONFIG_I2C=y and CONFIG_I2C_SHELL=y (and dependencies) are configured on an nRF54L15.
When I use P1...
On the device we're developing (small battery powered sensor tag, Thread Sleepy End Device usinc NCS v2.7.0), when trying to discover DNS services using the `otDnsClientBrowse...
We have the Nordic nRF54L15-DK PCA10156 0.9.3 2025.19
We use nRF Connect for Desktop v5.2.1 and Programmer v4.7.2 and connect by USB to our ASI_nRF54L_DK1 001057739416....
Does Nordic have any libraries or solutions for negotiating with a USB C charger and requesting 9VDC for example? Or do you recommend that I use a separate dedicated ASIC...
nrf5340 NCS 3.1.0
Hello, I am trying to improve boot time and here are some spikes and timings. What I have found out is that CryptoCell init (hw_cc3xx_init_internal) takes...
Dear Nordic Team,
I'm currently working on an application that uses ACL and ISO to transmit data between 2 devices. ACL is used for transmitting operations that are then...
Hello,
I am developing using nrf5340 and optimizing the Bluetooth throughput currently.
Although experiments go well, there are a few things I would like to know more...
Recently, I've been evaluating the I2S interface of the 52840 to read ADC data from the TLV320ADC6140 chip.
The TLV320ADC6140 datasheet states that the chip supports TDM...
Hello everyone,
I’m a student currently working on a university project related to BLE-based positioning using the nRF54L15 and Channel Sounding .
In the documentation...
Zephyr board: nrf54l15dk_nrf54l15_cpuapp
Hi, we have a custom SPI NAND flash driver and are trying to create an external flash partition for our littlefs file system.
...
I'm very new to Zephyr so please be patient with me. I'm looking for an example that show me UARTs running on the following pins and setup. I have the echo_bot working with...
Hi
There is a github repo https://github.com/nrfconnect/Asset-Tracker-Template/tree/main that receives updates as of yesterday.
However on the documentation website...
I'm trying to get a previously fully functioning MQTT connection back up and running after some hardware difficulties, but am failing to get it to connect to the MQTT broker...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
