We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I used a script to write the Gateway and Headset to the nRF5340 Audio DK board.
I used VSCODE to write the Gateway source and Headset source to the RAYTAC board.
I tried...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are developing a mesh network. Our requirement is the one device can connect to three other devices...
Hello.
What is correct way to use AT%MDMEV commands(searh status) to establish connection after long PSM/sleep time (168h). Our devices are used to track wild animals so...
Hello,
I'm encountering persistent address conflict issues within my Nordic project.
Occasionally, when a device joins the network, I observe address conflict errors....
Hello,
I am trying to send an array which has 2048 bytes via UART. But, when I add a some delay to repeat the the UART transfer, the code gets stuck on the HardFault. I...
Hi Community,
I report this issue in github, it seems nobody reply me, so I ask here again.
lesson 8 exercise 3 solution build failed · Issue #9 · NordicDeveloperAcademy...
Hi,
in our application we use SDCard and USB stack with the following configuration:
The communication with the nRF5340 is done by using a Linux Embedded systems. When...
I think that the source of the nRF5340 Audio DK sample board is designed so that LED1 lights up when a connection is established with CIS.
We are thinking of connecting...
Hello,
I am using the ADC on my custom board, based on nRF9160.
I am getting correct results when measuring a known voltage. However, I noticed that the execution is very...
At the company I work for we are developing a keyboard with mouse capabilities via USB and BLE using the NRF5 17.1.0 SDK. We create the USB HID with the following SDK macro...
When using the nRF9160-DK, I flash the board with Asset Tracker V2 as provided by the instructions for the board here .
The board and SIM card are registered and the board...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
hi support team，
i was testing smp_svr, i want to add button to my application that once i press the button and reset, the device will stay in mcuboot (serial port mode...
