I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi there,
I would like to use SMP for DFU my Firmware and communicate with other SoC by one UART port. And then, in SMP protocol specification,I saw there is an ID (64)...
Hi,
I got a new nRF52DK, started working with it. After Blinky example, I tried UART example.
UART program is working fine. But Now i can't reprogram DK.
I tried to...
When I toggle pin 12, it toggles pin 11 as well. When I toggle pin 11, nothing happens. I also checked pins 13-18 to see if they were affected by both pin 11 & 12 and they...
Hello Everyone I am working on DFU over Mesh and followed this guide https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_dfu_README...
Hi,
I try to use: nRF52840 device (Master) + LIS3DH device (Slave) for I2C interface communication. When the I2C Sensor library of LIS3DH is not applied, the nRF52840 (master...
Hello,
we do have a custom board with a nRF52833 to stream sensor data to a mobile app. The board contains a 32 MHz crystal, but not a 32.768 kHz. We are using nRF Connect...
Hi,
Just wondering how to configure the BLE for an example use case given below:
A factory where there are 500 temperature sensors installed. What is the right approach...
The login dailog dialog doesn't pop after clicking sign in button if the width of the web page is less than 770 px. This is especially annoying when you are browsing the web...
Hello,
According to "GitHub - NordicPlayground_nrf52-ble-image-transfer-demo":
For the nRF52840 use the S140 v7.0.1, provided with SDK v16.0.0.
For the nRF52832 use...
Hi,
Currently, I am using the nrf52840 (ISP1807) for my device, I am presently flashing it with my pc with nrf connect program and taking the necessary pin out from the...
Hello,
Based on the nrf_cloud_mqtt_multi_service sample I am trying to create a MQTT connection to the nRF cloud.
I am able to successful create a connection, but after...
Hi,
I want to use Bluetooth LE in a project for nRF9160DK. My understanding is that the main program should run on the SiP nRF9160 and it will be the nRF5280 that will perform...
Where can I find a specification with time for advertising device waits after sent adv packet for connection from central to it?
What time I have for handle some logic on...
Hi,
I'm using nRF52840 dongle and nRF connect SDK 1.6.0 (Zephyr) to create a BLE HID + USB CDC device. Is it possible to jump to bootloader from application code (or ideally...
