But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I am aware, that I the PDK is deprecated and I plan to use a nRF5340-DK in the near future.
However, I would like to make use of the PDK I have sitting around and...
Dear Mate,
I am trying to build and flash a program by using (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com...
Dear all,
I'm using nRF52832 and using timers to turn on/off GPIOs.
I saw that timer0, 1 and 2 has 4 CC registers.
Right now, I'm using timer0 like this:
1) turn...
Hi team,
I have some doubts regarding mcuboot behavior on firmware failure.
1) Consider the situation I have flashed a new image , it will get validate before mcuboot...
Hi,
I'm trying to use XIP on our custom board running a nrf5340 with a different Flash memory than the one on the nrf5340-devkit.
The XIP worked on nrf5340dk, but now...
Hi,
I have an nRF9160 device which is going thru PTCRB cert. We are doing TRP/TIS and nRF9160 won't connect to the Anritsu MT8821C. Basically it tries to connect and just...
I have a working MQTT subscription list, when I add a new topic for subscription my subscribe fails with ENOMEM error -12.
If I remove another topic, I can add new topics...
I am looking for a way to set the TX power in Openthtread using Matter with the current version of the nRF-SDK. It appears I cannot find a solution which is up to date.
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , half of the 256KB flash memory space is taken by the Softdevice...
I am using an Nrf52840 and sdk V14.2.0.
My question is how to compute the battery voltage based on my hardware.
The hardware uses AIN0 to measure.
The hardware has a...
It seems this is a new problem with PCA10059 2.1.0, but not 2.0.0 or 2.0.1 that we previously used.
I use a nrf52-dk to connect its P19 to the SWD pins on the dongle. With...
Hi, I'm developing Matter Controller using the Chip-Tool as example from the original chip repo: https://github.com/project-chip/connectedhomeip
I am not using releases...
Hi guys. I want to evaluate nRF52840's OOB feature with an Android OS 12 device.
Instead of using NFC, can the nRF52840 send the OOB data (confirm value, random value, nRF52...
hello, I made a custom board that mounts a virgin nrf9160; its programming takes place via a tag connected to the segger programmer. I tried copying a whole chip with JFlash...
