But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
HI,
I'm trying to get an OLED display over SPI working but since I've no reaction yet, I probed the output and noticed it seems to have no write data hold time between MOSI...
Hi Devzone Members,
I'm brand new to Bluetooth development, and I wondered if someone would be kind enough to advise me?
Am I looking at the correct Nordic kit to begin...
Hello,
we have experienced multiple times during testing that nRF9160 Modem reported CEREG 2. After that it stopped generating any notifications and stopped connecting to...
Adverting mode changing from BLE_ADV_EVT_FAST to BLE_ADV_EVT_IDLE. Could you provide example for changing adverting mode from BLE_ADV_EVT_FAST to BLE_ADV_EVT_SLOW mode?
...
Dear all
I use VS Code with nrf Connect v1.9.1, DK is nrf52833. It has been working fine in terms of debug, but today it stopped working and give me a message like this...
Hello, Nordic team
We have been studying Nordic for some time and are now in the stage of product research and development. We bought an nrf9160DK from a local agent at...
Is it possible to download the Certificate from a file or memory to chip with the internal SDK function?
I intend to automate the installation of the certificate on the...
Hey, we are moving our projects from nRF5 SDK to nRF Connect SDK
Iam new to this SDK and Iam trying to add mesh features into the project, so I'm using Bluetooth mesh: Sensor...
On a custom board with the NRF9160 chip, performing `nrfjprog -f NRF91 --recover --log`, AND `nrfjprog.exe -f NRF91 --coprocessor CP_APPLICATION --recover --log`, I get: ...
Dear Community,
I am trying to run the HTTP application update sample. I can run the sample without issues, but after the download is completed, the app is not updated...
I am using an nrf9160DK with modem firmware v1.3.2.
I want to be able to send the "AT#" type of SLM-specific AT commands to the modem (and read the response back) via firmware...
Hi,
I have setup exactly as described in this page Bluetooth: Mesh sensor server — nRF Connect SDK 1.4.2 documentation (nordicsemi.com) ,
I can successfully read the temperature...
Hi
According to the documentation for the GNSS interface, information into non-volatile (NV) memory so that the information can be used when GNSS is restarted and also after...
Good day
Im trying out the central multilink BLE example on sdk 2.02 with VS Code zephyr. After adding the example, under source file there is a warning stating
"missing...
