We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello guys
We have a problem with the SPI bus driver on the nRF9160 MCU. In our project, we use SPI1 and SPI3 instances.
When I send a package in some of these SPI busses...
Hello, after the excellent Nordic Techtour yesterday, I decided to try and implement the nordic distance toolbox.
However, my available hardware (52DK) is not supported...
Hi!
I'm developing a project on visual studio with ncs sdk V1.8.0. For a while, I was able to debug my project with no problem. But out of the blue, I'm no longer able to...
Hello,
While working on optimizing battery life, i noticed something strange.. This particular code actually does almost nothing other than setting low power mode (instead...
I'm trying to view core dumps on Memfault's web app, and having trouble doing so. I can't even see hard faults being logged even though I know they're occurring (forcing stack...
in the nRF52840, SPIM3 allows for high speed >4MHz communication. But I cannot see if there are dedicated pins specific to this mode, or can i map any pin to the SPIM3 high...
Hi Team,
As part of our requirement we need to fix the Advertisement to one fixed channel instead of altering between 3 channels like 37,38 and 39. If we have any sample...
Hello,
Using own BLE stack here (not SoftDevice) and having troubles with LL certification test cases with particular problem:
the tester establishes connection and...
Hi,
I would like to take current & power measurements of the nRF52833 SoC with the desired firmware file flashed to it. I am testing an application that uses the CPU temperature...
We are trying to make it so that we can permanently make one channel on the BLE module only for advertising while having the other channels flexible for other needs.
Hello, I have nrf52DK (nrf52832-PCA10040) and I wanted to test the Peripheral example in the nrf Connect SDK. I have built the project for nrf52DK_nrf52832 and then flashed...
Hi,
I am developing app using ant softdevice s212. I want nrf52832 to enter system off and stay there until interrupt from sensor occures. This interrupt is connected with...
I use nrf5340 to build esb project, I use the following code to scan rssi of different channels, but I read the value of NRF_RADIO->EVENTS_RSSIEND is 127, I hope you can tell...
Dear ,
How do I enable DCDCEN mode if I am using NCS1.8.0 SDK? Is there any Kconfig setting I need to perform to make this available?
Thanks and regards, Kevin
Hi,
Just wonder does NVS only use half of the configured size? I have configured the nvs_storage size = 0x2000 ( 8192 bytes)
So sector_count = 2 (4096 / sector)
When...
