But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello everyone,
I am developing an application, with the nRF52840 chip (actually BMD-380 ) , that streams via BLE data read by an SPI sensor (ADS1293) to an Ubuntu machine...
I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned.
I want to know...
We have a requirement of sending data to nrf mesh app without provisioning. So Can we use health server model to send data on app without provisioning?
The reason we choose...
My understanding is that the Modem Library is a dedicated interface to the internal modem in the nRF9160.
We also need a 2nd modem interface to an external device that also...
Hi
We are developing a system based on nrf desktop application of nRF Connect SDK 1.90. There are 4 devices in this system: a dongle, a central device and two peripheral...
Hello Nordic Team,
From the below link and few other sources
nRF52840 SDK16 - BLE Descriptors and Notifications - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
I have read through similar posts, though none seem to talk directly about the DK and the JLink OB (SAM IC) missing bytes itself.
To start off with, I have created a basic...
From various pages I copied together this code to read the reset reason:
However, I believe most of those pages were for nRF5 SDK. (It's not always clear.)
Is this still...
Hi Nordic
I used the nrf_gpio_cfg_sense_input() API to initialize the GPIO4 for waking up nrf52832 from system off mode, This IO could wake up nrf52832 successfully, but...
These two func:"softdevice_ble_evt_handler_set "
and "softdevice_sys_evt_handler_set" suggests that there are two categories/sets of events grouped into system & BLE.
...
I'm a user of nRF52 DK with S132.
I want to modify the event handler in the example application code such as ble_uart_c.
Where can i find the full list and description of...
Hello
Can I use the LORAWAN module with NRF52833? if yes, is the LORA gateway also required to send the data to the cloud, or can it be done directly without a gateway?...
TX :52840
Software version：nRF5_SDK_16.0.0_98a08e2 hardware version：
RX:52820
Software version：nRF5_SDK_17.1.0_ddde560
My test method: send 60 bytes of data through...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
