This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have a Nordic Thingy:52 and Nordic Thingy:91, and I want to develop custom embedded software for them. Do I need a J-TAG or can I flash code using USB?
I've seen tutorials...
Hello,
I'm starting development with nordic arm processors. Therefore we purchased the BMD-360 EVK. This board features the NRF52811 processor and has the same pins as the...
We currently have a nRF52840 central device written with the Bluetooth Nordic SoftDevice API. From what I have read, the Zephyr RTOS is the best way going forward. I started...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello ,
I on the DK nRF52840, I wanted to manage the sleep mode and measure the current consumed by the microcontroller.
I started with example uart, I cut the PCB track...
According to the Nordic infocenter here
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf9160%2FCOMP%2Fnrf9160%2Fnrf9160_operator_certifications.html&cp...
I am using nRF52840DK for working on my application. I use nRF Connect SDK v1.9.1 to run example and build application. I use VS code to build the application. I am working...
HI
Saw the youtude video: https://www.youtube.com/watch?v=dpvNXQiLbh4
For BLE Audio Broadcast mode, could i check how many channels of audio can be broadcasted and selectable...
I'm developing firmware for a custom board developed with the nRF5340. We opted to use RTT as our logging/shell output as opposed to UART thanks to pcb size limitations. I...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I'm trying to build the nRF5340 Audio sample application for the nRF5340 Audio DK board and get this error message when creating the project:
Any thoughts?
Regards...
I'm trying to migrate from the nRF52832 to the nRF52833 using the same exact code, but the nRF52833 does not go into low power mode. The nRF52832 consumes 100uA with the nRF52833...
Hello, I have successfully connected two NRF5340s using central_uart and peripheral_uart and can send messages to each other. But I don't know how to test the data rate.
I have an implementation that is using a PWM output to drive a LED. It has been observed that when the LED is on in a constant drive state, fixed PWM output train, the LED...
I would like to communicate at a speed of 1ms or 2ms if possible, as I need to make a gaming mouse with as little latency as possible. To achieve this, I plan to use the nRF52840...
