But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I have modified flash_placement.xml to define a 64 byte RAM region to be used to preserve data across soft resets. It compiles and links but the memory seems to be...
Hello, I was wondering if I can get some help with implementing a power On and power OFF functionality for our system.
We are using the nRF52810 chip with a custom PCB....
Hi,
I have a SPI Peripheral connected with nrf52832 EVK to check working of SPI interface.
I am writing a 10 bytes of data to a specific address and read back from specific...
I have been using the Nordic Power Profiler Kit 2 with the Nordic Power Profiler application for reading current measurements on an external device and have been saving/exporting...
I recently updated to nRF Connect SDK v1.8.0 from v1.5.0 and am encountering a new error with the same code. The error occurs when I call bt_le_ext_adv_set_data. My advertising...
This is in regards to my last post here: https://devzone.nordicsemi.com/f/nordic-q-a/84016/switching-between-two-applications-using-nrf5-sdk
I am using FreeRTOS.
Both...
During the development process, I had no trouble bonding with the rfConnect (current version from the website). After many changes to code, I got it to bond one time and deleted...
Hi,
Is it possible to use "nearby fast pair" technology on the nRF52833 platform? are there any examples of the use of this technology?
Best regards,
KaEd1705
Hi, I am using libuartes and when I receive text from other device my nrf52833 will respone "textAT1_Uart1". But I can not free them (using &libuartes1 because I'm using 2...
In nordic ncs zephyr use Nordi ble controller (SDC) else in zephyr mainline will use a software version of the controller that use LLL (BLE CONTROLLER).
Il possible to know...
I'm trying to create a minimal executable that has a structure placed at a specific address in flash. It looks like CONFIG_CODE_DATA_RELOCATION is needed to do this. However...
Hello,
we are trying to get the uart secure bootloader running on the nRF52820. When linking we receive the error message that RTC1_IRQHandler is defined multiple times...
For an upcoming product based on the nRF52811 chipset I wanted to prepare for the arrival of the new AP-Protect variant of that chipset and have a unified firmware that runs...
I'm using SDK12 and SDK15 on nRF52832 and nRF52840 (peripheral and central), although this would appear to be an issue with other devices too.
If I connect with NRF Connect...
Potentially related to : nRF Connect v3.9.3 does not detect external j Link programmer - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) , but I don't see the...
