But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
https://devzone.nordicsemi.com/f/nordic-q-a/65059/buttonless-dfu-on-nrf52832
When I try to DFU from NORDIC_BUTTONLESS , nRFConnect disconnects from it and connects to DFUTARG...
Hello,
I get an error message when running this function:
int ret = i2c_reg_write_byte(data->dev, cfg->i2c_addr, LSM6DSOX_INT1_CTRL, test);
I know 0x0BAE0002 error means...
Hello, With nRF5 SDK 17.1.0 release a new ifdef NRF_BLE_LESC_GENERATE_NEW_KEYS in nrf_ble_lesc.c has been added. Could you please clarify what the intention is of this generating...
Hello Team Nordic,
I think there is still a problem in the SDK 17.1.0 if not using a Softdevice (with SD all is OK):
in "nrf_drv_clock.c" -> "nrf_drv_clock_init(void)...
Hello Nordic team,
I am building an IoT solution and plan to use the nrf9160 just as a stand alone modem. App will reside on a separate MCU and talk to Nrf9160 on uart...
HI,
I am developing weight scale with Bluetooth feature. I have already developed the code to get weight scale reading using SPI example.
Also tested ble_app_uart code...
Hello,
I have currently cloned and built the latest master branch of Eclipse MQTT-SN Gateway https://github.com/eclipse/paho.mqtt-sn.embedded-c.git on my Nordic Border...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.4.0 to 1.5.1) and the Modem firmware (1.2.2 to 1.2.3) on my nrf9160 DK devices, the date time isn't synchronized...
Hello there,
It is actually basic for the Bluetooth connection for the nrf52840 using Zephyr, which changed the scan filter by name based on the central UART sample.
As...
Hi there,
We are currently using IAR embedded workbecnh IDE for our development on non-Nordic products. We are thus considering the possibility of also porting our Nordic...
Hi Nordic Support,
I am getting zero distance value from sensor(vl53l0x). I used SLAVE_ADDRESS =0x29 and register address=0x01. My code is mentioned below
void data_handler...
We originally saw (and reported) this problem with nRF5 SDK 4.1.0. We switched to nRF Connect SDK 1.6.0 which did not exhibit this problem. Now we just tested with nRF Connect...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
