We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I would like to add DFU support to my product.
How can I protect from people producing/buying counterfeiter boards and flashing my software on these boards ?
Do...
Hi,
I implemented two services, now I have the following problem. Each service is working standalone, but when I put both together only the first initialized service works...
Hi
I'm trying to get an ANT example running on the PCA10028 but I can't make it work.
All supplied make files are for nrf52 based boards.
As I understand it, I need to...
I have tried many different initialize setting, however the ACK could not be received in pine 1 to 5. The PRX can receive all of the 6 pipes. It works for pipe 0 only. Would...
Hello, sorry if this is a stupid question.I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.I want to modify ble_app_hids_keyboard
to be able to send Volumn_up/down keys to android...
Hello:
I am use nrf51822 to transfor data (BLE <->UART),i need a faster rate in ble , and i found a way in the zone,that to use BLE_EVT_TX_COMPLETE to send data, the send...
I would like to use the A/D converter to monitor the battery voltage and need to know if the 0.6V reference is generated with a bandgap or some sort of divider network.
...
Hi,
Next problem I've experienced is jumping processor to Hardfault state at sd_ble_gap_adv_start
with whitelist and BLE_GAP_ADV_FP_FILTER_CONNREQ .
In case adv_params...
Hi
Although I followed and got working eclipse Mars on win10 using this great @Vidar tutorial I am still having problem creating a new project under eclipse for any of...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...