But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
We are using a Nordic nRF52840 microcontroller alongside the nPM1300 power management IC. When the battery is switched off due to low voltage (undervoltage protection), the...
Dear Nordic Support Team,
I am reaching out for assistance with an issue I’ve encountered on my new nRF7002DK board. After successfully flashing the Azure IoT Hub example...
I work on NCS 2.8.0
I add follow to CMakeLists.txt
add_custom_target (
my_release_file
echo AAAA BBBB CCCC
DEPENDS all
)
when run "west build -b nrf54l15dk...
Hey all,
I'm working on a project where data gets written to an SD Card regularly. At reset, power to 3.3V to the SD card is activated and all runs relatively well.
I...
Hello,
For my project I am making a custom circuit board which is pretty much just the nRF52832 chip and the surrounding capacitors and whatnot. I'd like to program this...
Nrfconnect 2.7 worked fine, but I updated to 2.8 and get this error.
For this line, I try to access my internal flash storage partition offset.
The macro complains...
OS:Ubuntu
Board: nrf52840DK
SDK: NRF Connect SDK (master branch)
After building provided example: Bluetooth: HCI Power Control and flashing the board, in serial monitor...
I am trying to program the BC832 ( https ://www .fanstel .com /bt832 -1 ) using the NRF52DK (NRF52832). BC832 is a Bluetooth Low Energy (BLE) 5.3 with NFC module using Nordic...
Hi I want to make changes to the BLE Controller stack to create an implementation of a NWP. It involves 'core' changes. Can I use the 'nrf connect' ecosystem as it comes with...
Hello,
I just started to understand Zigbee and I had some problem. I created 3 endpoints. In one of them (endpoint counter_ep ) I need a attribute reporting. A reporting...
Hello,
We are certifying our custom board which includes the nRF7002. Part of the spec EN 301 893 procedure for adaptivity (5.4.9.2.2.2) requires a multi-channel validation...
Hi,
I am trying to develop a small Zigbee device that has two endpoints, each with a Temperature Measurement Cluster. My starting point was https://docs.nordicsemi.com/bundle...
I am currently migrating from ncs 2.5.0 to 2.7.0 and am trying to move to using sysbuild instead of child / parent image. I have an out of tree flash driver that currently...
I'm a software guy with a bit of embedded dev experience and trying to get the LED_strip sample to work in v2.8. I got the code working in 2.61, and discovered that a 2.8...
I can only find the 1.3.0 nRF52 DK Hardware User Guide version / revision on your site.
I need the nRF52 DK Hardware User Guide version / revision 1.2.4 for my SDK - it...
