But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I built and ran the Matter Light Bulb example for Thread and was able to commission it into Home Assistant with no issues. However, when I tired the Matter Temperature Sensor...
Hi
Setup: nPM1300, nRF54L15-based board, SDK 2.9.2
I am trying to figure out how to use the nPM1300.
So far, I have not succeeded. Quite frequently, after power...
Hi,
I downloaded the NCS v3.2.0, but always got the error below when u npacking the toolchain , the same error when downloading via Vscode. and there is no problem for v3...
Hello all, I am using the nRF52840 together with the nRF7000. To save GPIOs, I would like to use the BUCKEN pin (which is directly connected to the nRF7000) also as the enable...
I tried to compile the project according to the link（ https://github.com/nordicsemi-neuton/nrf-edgeai-thingy53-ble-remotecontrol ）, but the compilation failed.
The compilation...
Hello Nordic Community,
I am working with the nRF5340 SoC as the master and trying to configure a PDM microphone . I have two related queries regarding PDM/DMIC operation...
I use the nRF5 SDK for BLE peripheral development based on a keyboard example. After the peripheral connects and bonds with a central device, I can detect button presses....
Good afternoon,
I am trying to set up FOTA update over NB-IoT, my device is offline most of the time and connects only a few times a day.
1. What are the gudielines...
Hi I have a urgent production problem about the Nrf5340 chip.
In all my pre production, I use nrf5340DK to program my designed board using the jlink through jtag 10pin cable...
Hi,
I want to confirm that on the nrf9160, for pin assignments, any pin can be assigned to any peripheral (instantiation)?
So it doesn't matter what of the available...
If you have tested the nRF9151's GPS with the CMW100 or IQ station. We need to know: 1. What test waveform file is required? 2. Should we use the ARB file or the CW waveform...
I'm trying to experiment with Bluetooth Channel Sounding using the nRF Toolbox App with an nRF54L15-DK. The app is running on a Google Pixel 10 running Android 16 QPR3 Beta...
From: https://github.com/zephyrproject-rtos/zephyr/issues/103807 Describe the bug
Hello,
I have configured a project based on the nRF5340 DK board and added a debounce...
Hi, So, I want to do BLE DFU from one nRF52 MCU to another nRF52 MCU. The start point for me was this:
put SMP server sample on one nrf52dk (this device is advertising...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
