This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm using the Fanstel BC832 module which contains Nordic's nRF52832 BLE chip on a custom PCB board. When trying to run the Blinky example on PlatformIO, it works...
Hello,
we are debugging the asset_tracker_v2 on nRF9160 DK in VS Code with the nRF Debug backend, but unfortunately the global and static variables are not shown in the...
Hello,
Can the SAADC driver be modified to be used in a polling mode instead of interrupt?
E.g. I modify the driver to not use any interrupt(comment out interrupt enabling...
Our project uses nrf5340, and we hope to match it with two wm8904 audio chips. They communicate with each other using the I2S protocol. However, we noticed that two I2S buses...
Greetings,
I am trying to pair nRF52840 DK to second admin (controller) using the provided chip-tool and the switch app from the nrf samples.
Specs:
nRF52840 DK (DUT...
Hi, So I I'm working with nRF52833_xxAA on a custom board. I want to be able to debug without erasing all after power reset so I followed this tutorial.
And I was following...
We would like to try using the standard DFU process to update third party device connected to the nrf52 chip.
For proof-of-concept I want to use DFU update with experimental...
The toolchain manager always fails with the following error: Failed to clone the repositories: env: bash: No such file or directory
MacOS Big Sur
nRF Connect for Desktop...
This is more of a zephyr question I suppose, but is there anywhere I can look at a list of setting key values pairs? Or alternatively what is the best way for getting the...
Hi
For nRF52840 as Zigbee Coordinator, for an unknown new device (ED), after the new device joins the Zigbee network,
Is it possible to know the Profile, End-Point,...
Hello, guys!
We have FCC/CE/UKCA/RCM/EAC certified board that contains nRF51822 SoC. We currently don't have a possibility to enable the internal DC/DC regulator of nRF51822...
Hi,
I am moving from FreeRTOS to Zephyr. So I jused some of your simple example for trying to understand basics. I edited it little bit.
I have some default task from...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
To achieve the maximum transfer rate over ESB, I added the following expression to the ESB initialization function:
NRF_RADIO->MODECNF0 = (NRF_RADIO->MODECNF0 & ~RADIO_MODECNF0_RU_Msk...
