This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Before using J-Link script to upgrade firmware, offsetStart (0x0) and offsetEnd (0x32E06) are correct. But after using J-Link script to upgrade firmware, offsetStart (0xADDEFE01...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to enable 2Mbps data rate. So I've added The following code in both peripheral and central.
ble_gap_phys_t...
I try to create new application using worspace type but fail , if I use freestanding type is OK. I already downlad and install SDK 2.0 . What happen? Could someone help me...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
hi
i'm new to the nRF platform and realised it uses zephyr. i come from a pic & stm32 background with little rtos knowledge and find the official zephyr cryptic. especially...
I created a BLE device with custom characteristic showing the sensor value (int16). But I can't achieve 1khz sampling rate.
1. Is sending data via NUS faster since the central...
I would like to using Keil to build secure_bootloader project for changing NRF_DFU_BLE_REQUIRES_BONDS from 0 to 1. But Keil failed to build. Please refer to snapshot of Keil...
Hi, I am using a third party module based on nRF52840. I want to use a standard UART to operate the CLI shell. I am not clear how to do this, any help?
Thanks,
Kaus...
Hi,
I am trying to run a sample "Beacon" that a sample of nrf5340 about bluetooth.
but, there is one issue as follow when i run each sample about bluetooth :
Bluetooth...
hi，
the project https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
if this project can't build in windows platform？
thanks...
nRF 5 SDK 17.0.2
I am working on getting the nfc_pairing_reference example application migrated to S140 on two nrf52840 DKs. I have successfully ported the hardware, the...
We have a customer interest in developing a BlueZ application using the nRF52840.
This will be using the ARM9 CPU Atmel SAM9G25.
These are some of the software versions...
Environment introduction:
1. Use software SEGGER Embedded Studio for ARM (Nordic Edition) V5.50a.
2. 52833-DK*3 And EK42442ds *2
3. Switch order ANT1>ANT2>ANT3>ANT4...
Hello Group,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I was...
