But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
Hi,
Our customer needs CAT-M, CAT-NB, GPS RF test data
I see that devZone has less information about CAT-M, CAT-NB and GPS RF performance tests
1. Please provide GPS...
As requested I am posting a public question based on Nordic's request here:
https://www.linkedin.com/feed/update/urn%3Ali%3Aactivity%3A6911310498537869312/?commentUrn=urn...
Hi,
parameters A NRF_SDH_CLOCK_LF_RC_CTIV
parameters B NRF_SDH_CLOCK_LF_RC_TEMP_CTIV
1. The internal RC parameter should be configured as follows, but how are parameters...
If AT+CFUN=1 will not get modem connected/registered to a network, what retry algorithm does the nRF9160 implement? Is it something like exponential back-off algorithm?
I'm attempting to add NVS functionality to my code. Had a play around with the zephyr/samples/subsys/nvs example. It was working originally, and then when I started porting...
Hi!
For a project I need to sample an I2C sensor for a period of 1 min with 1 sec between samples with a nordic nrf52832. During this 1 min, a co-processor communicates...
I'm trying to build a custom board in VS Code to use with the nRF9160. I'm using a Thingy91, so I took the board file for that, and copied it into the project directory. ...
