This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
Hi,
I want to trigger a wake up from System ON sleep (WFE) using the LDETECT signal on Zephyr.
I managed to wake up using Zephyr's gpio API but my understanding is that...
1. Nrf52840 acts as central and Nrf52832 acts as peripheral. when nrf52840 has connected with nrf52832, nrf52832 disconnected occasionally. Disconnect reason 0x0013. When...
Hi there!
I have recently managed to combine sht85 with light lightness server code. J-link is able to produce 2 values (Temperature and Humidity) whenever I key in the...
I has successfully built the following demos and run them on a nrf52840 dongle (board: nrf52840dongle_nrf52840) :
cdc-acm-console demo from Samples and Demos » Various...
Hello,
I'm struggling with DeviceTree support in Segger Embedded Studio and nRF5340. I want to use the I2C Modul.
So I defined in my (dts)overlay file
&i2c0 { status...
Hello,
I recently updated my nRF Connect to the latest version 3.9.3 and it also updated the programmer app to 2.1.0. After this update, the Programmer app does not detect...
Upload fail - Remote DFU invalid CRC error
i m facing this error while uploading firmware through DFU kindly any one help me to fix this issue using nRF 52810
Thanks
Trying to update the Thingy91. While the nRF52840 updates ok, nRFConnect for Desktop reports " No matching trait found" when trying to update the modem on the nRF91.
The...
I updated programmer to v2.1.0 plugged in my device to add an updated .hex file but now programmer can't find my device. I have to put the device into reset mode so programmer...
Hi,
I am using ble_app_uart and SPI example to develop the wireless weight scale.
Till now I have successfully integrated SPI and ble_app_uart example to display weight...
Hello~
The environment： Chip is nrf52820，SDK version is 17.0.2，sd version is s112_7.2.0.
pic1:
Pic1 the APP code that I wrote for this problem. When I only burned...
Hello, I wanted to test the VS Code extension but it failed for the following use case...
In our company, we are building our product-related SDK that uses nRF Connect...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
