This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi Everyone We are using nrf52840 for our custom PCB along with QSPI memory. We are using W25Q128FV as our qspi memory chip.
This function mentioned below is used to initlaize...
Hi,
I want to read and write the data from IS25LP064A NOR flash with QSPI. I am using the QSPI example from SDK v16. Please let me know how to get started with QSPI in order...
Hi,
I am wanting some information about any guarantees on the ordering of queued notifications and indications. According to https://devzone.nordicsemi.com/f/nordic-q-a...
SoC nrf52840, nrf connect SDK v1.4.2
we have a board with 3 sensors connected with independent SPI interfaces. after porting the code to ncs v1.4.2 from v1.2.0 the SPI communication...
Hi ...
I am getting the occasional error NRFX_TWI_EVT_BUS_ERROR being reported from the twi_irq_handler()
You can see in the following code snippet from this function...
I am using SDK17, nRF52840 based custom board and SoftDevice 7.2.0 with SES.
I want to use SDK's secure bootloader (pca10056_s140_ble) with my own keys.
To enter to...
Hi,
I have used a Custom board using nrf52832. It follows some procedures. After that, it needs to get into sleep mode for a time which was sent from the app
I use the SEGGER Embedded Studio for ARM IDE to build a clean build directory. From the IDE I can build the project and it completes successfully.
So I then take the same...
We have a product that uses a module containing NR52832 and also both 32kHz and 32MHz crystals. This has been operating correctly and is in full scale production.
On our...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
