But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I'm new to development with the Nordic SDK for the nRF52840 and during evaluation I run into the following problem with the UART ports, which I cannot resolve after hours...
Hi,
I'm looking for a way to access the PDU header data from received BLE advertisements, but I can't find where it is stored. I see that the payload is in p_ble_gap_evt...
Hello every one:
I had modified the light-switch example into a model that can sent and receive multiple bytes.It is work fine when I set the num of bytes less than 10 bytes...
Hi, I have bricked a nrf9160-DK, and was wondering if someone could provide me with a complete firmware image, including secure bootloader, application (AT or Asset tracker...
Hi,
I currently developing my own NRF9160 board Based on NRF9160 DK schematics. My question is, can we remove all passive antenna circuit with all matching network and...
I am using the Fanstel BT840 module with an Epson FC-135 32.7680KA-AC3 crystal and 12pF NPO caps. It functions well in indoor conditions but the LF oscillator stops if placed...
Hi,
I am following this tutorial ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_blinky.html ) to learn how to...
Hello,
I have nrf51822 based Board,
and I need to make Android app for scan and modify Beacon's data.
I found "nRF Beacon" App's source code in GitHub,
and I try...
Hi,
I have seen that there are three most useful topology for mesh : Bluetooth mesh, zigbee and Thread
What parameter should we have to take in consider when selecting...
I'm trying to use a timer with S130, but it doesn't seem to tick:
void timer_event_handler(nrf_timer_event_t event_type, void * p_context) {
NRF_LOG_INFO("Timer 1 interrupt...
Hi,
I recently started experimenting with nRF52840 eval-kits and a nRF52840 dongle using the generic onoff client and server. I used my phone and the nRF Mesh App to offload...
I learning NRF52832 beacon using SDK15.2 i tested code ble_app_beacon code in non connectable beacon mode its working fine. how can i change this code like connectable beacon...
Hey, I would like to add BLE mesh functionality to my existing project which is based on the firmware v2.2.0 https://github.com/NordicSemiconductor/Nordic-Thingy52-FW . I...
I'm planning to connect The nRF52840 MCU GPIO in series to a 1.8V 20mA LED and a Resistor then to ground.
Would the current from the MCU be sufficient to power the LED ...
Hi,
Here is my issue, I don't enter in bootloader by using the buttonless DFU characteristic. Here below I expose my action and what it happens. Thank you in advance for...
