But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
We have a RCU on the chip nrf51822-qfaa s110. Sometimes (the period is not deterministic) occurs a situation that the remote stop responding to key presses. But at...
I am trying to write to NRF_POWER->GPREGRET to store some variables that should be retained through a software reset.
I am running SD 5, SDK 14 and using GCC to compile...
I would like to write a program to communicate directly to the Dongle over USB. The plan is for manufacturing test fixtures to communicate with the 'device under test' over...
Hi all,
I want to disable SD and reinit SD and reinit my services.
I try by ble_app_uart example.
I add code for button, when I press button 1, it disable SD. When I...
Hi,
I just started working with Nordic chips so I apologize if I am missing something obvious here
I am using a custom board that I designed containing a nrf52832 module...
First of all, Because of my poor English, and I'm newbie this kind of work.
I'm not sure you can understand my question. But I'll try
Currently, To see my borad's log...
Hi everyone,
I am trying to implement my device with nus service. Both nus client and server role on the same device, similar to the official example of "relay".
But when...
Hi everyone,
I would like to build the Bluetooth network having three devices such that any two of them could communicate with each other. Is it possible to do it with nrf52832...
Hello,
I got Thingy:52-SDK-zip from https://www.nordicsemi.com/Software-and-Tools/Development-Kits/Nordic-Thingy-52/Download
and I did all setps wrote in README.md. Then...
Good day!
As base I used this examples:
ble_app_multiperipheral - for connection handling
ble_app_hids_keyboard - for whitelist and bonding
Error occurs after...
I am inquiring about the ability of the nRF9160, does the device have the resource to be a picocell? Specifically, can it handle communication to and from a single cell phone...
Hi
I‘m working with the SDK since many versions. One thing I don‘t understand is the sdk_config.h concept.
My first thought was that there is a master sdk_config.h in...
Hi, I made a PCB board nrf51822.
Because of my mistake, Rx, Tx pin was not cross connected to MCU.
So i want to change Rx <-> Tx pin.
In the example of ble_app_uart_s130_pca10028...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
