This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi
I saw a fail for RF-PHY/RCV/BV-29-C on nRF52840 DK.
But I also find it is a known issue as "Anomaly 172 Addendum".
In the nRF52840_Rev_1_Errata_v1.2.pdf, two workarounds...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
Hi
I have this code that works like a charm when the device is connected and I want it to leave the network.
But if the device is dead or disconnected and I want to remove...
Hi,
I know this is a license question and the default answer is "contact a lawyer if you don't understand the license". But this can hardly be the first time someone...
Hi,
I'm trying to connect nrf52840 to IOS 12.1.4 as a Braille display. Standard BLE HID is working well, but when I try to connect as a Braille Display ( Settings/General...
I am trying to connect and according to the spec sheet, there might be multiple pipestatusevents.
When I try to connect using different phones (with different Bluetooth...
Hi,
I'm using the light switch client example to test the Mesh App on iOS.
The PCA10040 board can be identified through Mesh App, but not be identified on our test board...
I am using nrf52810 chip without softdevice or bluetooth stack. I started to develop at November 2017 with Datasheet version v1.2. On 31. Januar 2019 Nordic released a newer...
Hello,
I have project for collecting temperature information from 15 pcs temperature sensor.
It is possible to create system with 16 pcs nRF52840.
one of them will be...
Hello,
I’m using two nrf52832 as servers sending 20 Byte data with 18 ms notification interval.
Notification Data:
[incremented uint8_t ] [19 byte data]
Client:...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
I am converting the simple_on_off vendor model to send a message on mesh 3.1.
the server implemented the simple_on_off model successfully. But but my client runs into 0...
