But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I need to connect a device to an nRF5340 SPI port without creating a custom driver. I'm tempted to use the nrfx_spim driver directly, but I'm trying to do it with Zephyr and...
Hi,
I am migrating from nCS v2.6.1 to v2.9.0, my workspace builds fine on v2.6.1 But on v2.9.0 I am getting the below error:
This is being generated as my main.c has...
Hi
i want to generate security key with the combination of time and private key.can i acheive it in NRF..mainly in NRF52833?
i have a ref code in this repo.. here can...
Hi,
My goal is to primarily save the audio being generated by the Headset device in the LE Audio samples. I have established Bidirectional stream between the Headset and...
I had received a lot of support in: Replacing RS485 link with NRF24L01+ .
At the moment I have 95% proyect working OK but in one operation mode of my program, after some...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
