Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi everyone,
I’ve just started my adventure with the nRF52xxx family and have already hit a wall. In my previous project, I successfully programmed an nRF52840 dongle, but...
Hi, i want to use the coded PHY for advertising but cannot get it working. I configure the advertising source with these params:
and start the scanning of the sink like...
Hello,The Nordic Team
I have developed a SED product based on the Matter Over Thread protocol. I want to add a real-time time function on the device side. I have learned...
IDE：SES for ARM V5.42a
SDK：nRF5_SDK_16.0.0
I am develop BLE device with nRF52832. I found that some global variables were assigned ramdom values if I enable UART easyDMA...
Hi,
i am asking for the configuration for power profiler kit ii setup to the nrf54l15. The reason was when i removed the jumper from P6, the external sensors which were...
Hi all,
I already successfully read the instant mode VBAT from my PMIC, nPM2100, but I would like to have more precise VBat readings.
1. I used this set up for my avg16...
Could anyone help me solve this? Everytime i run a program without the templates it always gives me this REST auth token is malformed, but I have never used a auth token before...
Hi,
I'm using nRF52840 BLE Dongle to connect and perform bonding to a custom target.
The connection and bonding are working but I need to write a token (lenght=291)...
Hi, Our application is running in the central role connected to a peripheral. The app disconnects from the peripheral by calling the bt_conn_disconnect() function. It appears...
Hello everyone, trying NRF for the first time and so far it's been only bunch of frustration and wasted time.
What I need to create is a subset of BM applications for NRF54L...
I am currently developing a HID device that supports BLE and USB. I have tested the firmware update function via both BLE and USB (USB CDC ACM). However, I am experiencing...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi all, I'm trying to enable the SPIM4 peripheral on the dedicated high-speed pins (P0.08 SCK, P0.09 MISO, P0.10 MOSI, P0.11 CS) on the nRF5340DK, but I'm seeing no activity...
Been trying to set up a project to run some basic openthread as a proof of concept project. I based much of it off the CLI example and SDK. I have gotten stuck where my code...
