After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
My device get deep sleep mode. It wakes up from reset button trigger. Because I couldn't gpio pin trigger for wakes up. So I put vibration sensor to reset pin. It wakes up...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
Hi,
I've been using the DWT macro cell successfully on the app core to provide high accuracy timing information. E.g., with these declarations:
and enabling the cycle...
hi ~
peripheral can bond how many smartphones ?
and What will happened if over bond?
i use sdk12.2 below 'is my setting
#define SEC_PARAM_BOND 1 #define SEC_PARAM_MITM...
Hi…
I am using freeRTOS V10.0.0 release
I am using nRF52820 + SDK V17.0.2 with SD112 V7.2.0 along with tickless idle as this is a battery based product…
When my application...
Hey guys, I'm an embedded software engineer and I am currently working in a prototype, specifically using the Circuitdojo Feather nRF9160 , I am also using a Hologram International...
Based on the Sample "Bluetooth Peripheral_uart:
My latest attempt to send long data stream:
I send:
1234567890123456789012345678901234567890123456789012345678901234567890...
Hi,
I've met a problem. It seems NVS sometimes erases sector during initialization.
As shown in following log, I wrote 2 datas(address, slot) in NVS. Normally, I can read...
Using the period required for 2Mbps Gazell, 600us, how much does this slow down BLE (bandwidth/# packets)? Also, does the timeslots API work well with nrf52? If I modify this...
Solved, just bad luck, I got 3 broken module, the 4 is ok.
So it module's problem.
======================================================= I am trying to flash "hello...
Hi,
is there any way adjust the ISO channel transmission power (e.g. -20dBm, +2dBm, ...) in the new nRF5340 Audio application? I saw that one can select between 0dBm and...
I have a Thingy91 that I want to connect to nRFcloud. Not knowing the state of its keys/provisioning I followed the procedure to generate just-in-time keys (as a first attempt...
Hello all!
I'm starting development of BLE Mesh network as part of my Master thesis, for which I designed a custom board based on nRF52832 and nRF52840 with some built-in...
I am working on nrf52840 using nrf connect sdk v2.0.0 example periodic_adv, nrf52840 is prodcasting extended advertising, my app is running on Sony Xperia 1 with bluetooth...
