Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am in the early stages of development and would like to proceed with only non-secure partitions on the nrf9160. I'd like to not make use of TrustZone.
I notice all of...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
What is the state of the GPIO pins during programming.
Because of space restraints, in order to get the the programming signals out from under the laird module we are...
Hello,
I am using a nrf52840-dk and communicate via SPI with an external board (NUCLEO-L476RG from ST) during development. For the development itself I am using the nRF...
Hi,
When starting to learn nRF currently, is it better to start with nRF5 SDK or nRF Connect SDK? I know Nordic will not add new features to nRF5 SDK, but what if I want...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
Hi All!)
I am using nrf52833/20 Dk and am able to connect the two devices using coded PHY connectable mode by the available examples ( BLE_App_Uart and BLE_App_Uart_C )...
Hi every body.
I have trying without success to attach an event handler function to the TWI.
I am reading a temperature and humidity sensor using I2C. In polling mode...
Dear Nordic Engineers
I would like to add usb bootloader to ble bootloader.
I modify config of pca10056_usb_debug/sdk_config.h and add .c .h file of pca10056_usb_debug...
Hi DevZone,
What I am working with:
I am working on a project using nRF Connect SDK with VS Code, and I am also using the nRF Connect extension for it.
My issue...
Commands sent by phone App to BLE UART end up in serial UART stream. Debug with breakpoint in the uart_event_handle shows NO stack entries, as though it popped out of Main...
To the kind attention of Nordic support team,
We are very interested indeed in finding sample AWTK porting on nRF52840 like in https://www.youtube.com/watch?v=zD-7YdxynLo...
my project requires a simultaneously data-collection from 13 IMUs sensors which we built with NRF51822 + BNO055 (IMU)
we used the Gazelle mode, I understand each host can...
